Analog Electronics Syllabus Wise e-Resources links

-
C203: Analog Electronic Engineering


Unit 1
APPLICATIONS OF SEMICONDUCTOR DEVICES

https://en.wikipedia.org/wiki/Diode   
http://www.electronics-tutorials.ws/diode/diode_3.html
http://www.learnabout-electronics.org/Semiconductors/diodes_20.php
video links:
https://www.electrical4u.com/video/index.php
Unit 2
SMALL SIGNAL ANALYSIS

https://en.wikipedia.org/wiki/Transistor
http://www.electronicshub.org/npn-transistor/
http://www.electronics-tutorials.ws/transistor/tran_4.html
video links:
https://www.electrical4u.com/video/index.php
https://www.youtube.com/watch?v=9CrcRabTQ0s
https://www.youtube.com/watch?v=SmZ2-Fhyoo0
Unit 3
FEED BACK AMPLIFIERS

https://en.wikipedia.org/wiki/Barkhausen_stability_criterion
https://en.wikipedia.org/wiki/Negative-feedback_amplifier
http://ecetutorials.com/question-answers/amplifier-question-and-answers-2/feedback-amplifiers/
http://www.electronics-tutorials.ws/oscillator/colpitts.html
video links:
https://www.youtube.com/watch?v=We6csSnDwVo
Unit 4
OP-AMP FUNDAMENTALS & CHARACTERISTICS

https://en.wikipedia.org/wiki/Operational_amplifier
https://electronicsforu.com/resources/learn-electronics/op-amp-basics-operational-amplifier
video links:
http://www.electronics-tutorials.ws/opamp/opamp_1.html
http://www.electronics-tutorials.ws/opamp/opamp_2.html
Unit 5
OP-AMP IC741 APPLICATIONS

http://www.electronics-tutorials.ws/opamp/opamp_4.html
https://www.allsyllabus.com/aj/note/ECE/LINEAR_ICs_and_APPLICATIONS/unit2/Clippers%20and%20Clampers.php#.Wg6__RWGPIU
https://en.wikipedia.org/wiki/Clipper_(electronics)
https://en.wikipedia.org/wiki/Schmitt_trigger
Unit 6
SPECIAL IC APPLICATIONS

http://www.electronicshub.org/understanding-555-timer/
http://www.electronics-tutorials.ws/waveforms/555_timer.html
http://www.niser.ac.in/sps/sites/default/files/basic_page/IC%20555%20multivibrator%20circuits.pdf

Comments

Post a Comment

Popular posts from this blog

207--DCMT Lab manual by Prof.A.A.Malgave

-
Image
Experiment no. 1 Object Load test on DC Shunt motor. Objectives To study the direct loading test of DC Shunt motor by Rope-Pulley arrangement method. Theory             This is direct method of testing the motor in which the motor is loaded gradually from no load to full load. The pulley is fitted on the shaft of a motor. A rope or leather belt is wound round the pulley & its two ends are attached to two spring balances F 1 & F 2 . The tension of the belt can be adjusted with the help of the wheel.             The force acting tangentially on the pulley is equal to the difference between two spring balance readings. i.e.       F = (F 1 - F 2 )     If         r = radius of pulley in meters,             N =...
Read more

Analog Electronics Lab Manual Experiment No 1-5

-
Experiment No. 1 Object: Familiarizations of Electronic Components and Usage of Multi-meter, Oscilloscope and Signal Generator Objective: 1.         Identification of Various Components (i.e Resister, Capacitor, Diodes) 2.         Familiarization with Breadboard, Multimeter, Power Supply, Oscilloscope & Signal Generator. Theory:                 Breadboard: Fig.1: A Typical Breadboard Fig.2: Connection Details A real breadboard is shown in Fig. 1 and the connection details on its rear side are shown in Fig. 2. The five holes in each individual column on either side of the central groove are electrically connected to each other, but remain insulated from all other sets of holes. In addition to the main columns of holes, however, you'll note four sets or groups of holes along the top and bottom. Each of these cons...
Read more

Analog Electronics Lab Manual Experiment No 6-11

-
Experiment No. 6 Objective Design of Simple Amplifier Circuit (Common Emitter) Objectives 1.         To design a common emitter transistor (NPN) amplifier circuit. 2.         To obtain the frequency response curve of the amplifier and to determine the Mid-frequency gain, A mid, lower and higher cutoff frequency of the amplifier circuit. Apparatus Required Sl.no Name of components Rating /Ranging Quantity 1 Transistor: 2 Resistors: 3 Capacitors: 4 Power Supply 5 Oscilloscope 6 Function Generator 7 Breadboard 8 Connecting wire Design: Before designing the circuit, one needs to know the circuit requirement or specifications. The circuit is normally biased for V CE  at the mid-point of load line with a specified collector current. Also, one needs to know the value of supply voltage V CC  and the range of β...
Read more